Chain Lubricators dispense oil by gravity from a reservoir through an adjustable needle valve. Available with manual or electro shutoff. These units have an adjustable oil feed rate which is observed through the lower sight chamber. Flow to brush is controlled by either the manual shutoff or by wiring a solenoid valve across the line of the drive motor, providing automatic operation. Reservoirs are transparent, break-resistant, high temperature plastic which allows quick visual check of oil supply. Various brush sizes and materials can be furnished for exceptional oil penetration to vital points and good cleaning action. Provision is made on most units for a minimum of 1/2" brush wear.
Style DEC
Style DOSC
| Electro Model No. |
Manual Model No. |
Capacity | A | Electro B | Manual B |
| B-1743-1 | B-1745-1 | 1 oz. | 2 | 5 | 4-1/2 |
| B-1743-2 | B-1745-2 | 2-1/2 oz. | 2 | 6 | 5-1/2 |
| B-1743-3 | B-1745-3 | 5 oz. | 2-7/8 | 5-15/16 | 5-7/16 |
| B-1743-4 | B-1745-4 | 9 oz. | 2-7/8 | 7-3/16 | 6-11/16 |
| B-1743-5 | B-1745-5 | 1 pt. | 3-5/8 | 8-1/2 | 8 |
| B-1743-6 | B-1745-6 | 1 qt. | 3-5/8 | 11-7/8 | 11-3/8 |
Larger Capacities Available
Brush Options
| Brush Size | Round Brush | Flat | Roto | |||
| 1/4 Dia. | 5/8 Dia. | 1 Dia. | 1 1/2 Dia. | 2 1/4 x 3/8 | 3 Dia. x 1" wide |
|
| D | 3 5/8 | 3 1/16 | 3 3/4 | 3 3/4 | 3 | 4 7/8 |
When Ordering Specify:
•Model Number
•Voltage & Frequency
•Brush size & brush material
Specification:
•Pressure...........................Atmospheric Pressure
Reservoir & Sight Vented
•Temperature......................225ºF. Max
•Brushes............................Nylon
or Stainless Steel Bristles
•Reservoir...........................Polycarbonate
•Seals................................Buna N
•Sight.................................Glass
•Filler Cap..........................Steel, Plated
•Valve
Body........................Aluminum Alloy
Valve Brushes consist of a metering valve with sight which is then connected to various styles of brushes. A mounting means is provided. Brushes can be adjusted for wear and are easily replaceable at low cost. All valve brushes can be supplied with nylon or stainless steel bristles.
| Model Number |
E |
|
| Straight | 45º Angled | |
| B-309-1 | B-310-1 | 2-1/4 |
| B-309-2 | B-310-2 | 4-1/2 |
| B-309-3 | B-310-3 | 6-3/4 |
| B-309-4 | B-310-4 | 9 |
| B-309-5 | B-310-5 | 11-1/4 |
| Model Number | Figure | Brush Size | D |
| A-2261-1 | 1 | 1/4 Dia. | 6-5/16 |
| A-2261-2 | 5/8 Dia. | 5-3/4 | |
| A-2261-3 | 1 Dia. | 6-7/16 | |
| A-2261-4 | 1-1/2 Dia. | ||
| A-2261-5 | 2 | 2-1/4 x 3/8 | 5-11/16 |
| A-2261-6 | 3 | 3 Dia. x 1 W. | 7-9/16 |
| Model Number | Brush Size | B | C | D |
| B-1009-1 | 1/4 Dia. | 1/4 | 3-3/8 | 4-13/16 |
| B-1009-2 | 5/8 Dia. | 4-1/4 | ||
| B-1009-3 | 1" Dia. | 3/4 | 4-15/16 | |
| B-1009-4 | 1-1/2 Dia | |||
| B-1009-5 | 2-1/4 x 3/8 | 3-5/8 | 3-1/2 |
| Model Number | Brush Size | D | |
| W/Drip Tube | Without | ||
| B-1008-1 | B-1049-1 | 1/4 Dia. | 4 |
| B-1008-2 | B-1049-2 | 5/8 Dia. | 3-7/16 |
| B-1008-3 | B-1049-3 | 1 Dia. | 4-1/8 |
| B-1008-4 | B-1049-4 | 1-1/2 Dia. | |
| B-1008-5 | B-1049-5 | 2-1/4 x 3/8 | 3-3/8 |
When Ordering Specify:
•Valve Brushes
•Model Number
•Bristle Material
Specifications:
•Temperature....................Above 250ºF. use Stainless Steel Brush
•Adapters.........................Aluminum Alloy
•Brackets.........................Steel, Plated
•Brushes..........................Nylon or Stainless Steel
•Valve
Body......................Steel, Plated
•Seals..............................Buna-N
Shank Brushes consist of brushes attached to holders. Mounting means are provided. Brushes can be adjusted for wear on most models and can easily be replaced at low cost. All shank brushes can be supplied with nylon or stainless steel bristles.
| Model Number | Brush Size |
| A-2048-1 | 2-1/4 x 3/8 |
| Model Number | Figure | Brush Size | D |
| A-2257-1 | 1 | 1/4 Dia. | 4 |
| A-2257-2 | 5/8 Dia. | 3-7/16 | |
| A-2257-3 | 1 Dia. | 4-1/8 | |
| A-2257-4 | 1-1/2 Dia. | ||
| A-2257-5 | 2 | 2-1/4 x 3/8 | 3-3/8 |
| A-2257-6 | 3 | 3 Dia. x 1 | 5-1/4 |
| Model Number | Figure | Brush Size | D |
| A-2256-1 | 4 | 1/4 Dia. | 4-1/8 |
| A-2256-2 | 5/8 Dia. | 3-9/16 | |
| A-2256-3 | 1 Dia. | 4-1/4 | |
| A-2256-4 | 1-1/2 Dia. | ||
| A-2256-5 | 5 | 2-1/4 x 3/8 | 3-1/2 |
| A-2256-6 | 6 | 3 Dia. x 1 | 5-3/8 |
| Model Number | Brush Size | No. of Inlets |
| A-2258-1 | 2-1/4 X 3/8 | 1 |
| A-2258-2 | 4-1/2 X 3/8 | 2 |
| A-2258-3 | 6-3/4 X 3/8 | 3 |
| A-2258-4 | 9 X 3/8 | 4 |
| A-2258-5 | 11-1/4 X 3/8 | 5 |
| Model Number | Brush Size | B | C | D |
| A-2260-1 | 1/4 Dia. | 1/4 | 3/4 | 4-13/16 |
| A-2260-2 | 5/8 Dia. | 4-1/4 | ||
| A-2260-3 | 1" Dia. | 3/4 | 4-15/16 | |
| A-2260-4 | 1-1/2 Dia. | |||
| A-2260-5 | 2-1/4 x 3/8 | 1 | 3-1/2 |
When Ordering Specify:
•Shank Brushes
•Model Number
•Bristle Material
Specifications:
•Temperature....................Above 250ºF. use Stainless Steel Brush
•Adapters.........................Aluminum Alloy
•Brackets.........................Steel, Plated
•Brushes..........................Nylon or Stainless Steel